Samsung Washer 4E or 4C Code: What It Means and How to Fix It

4E or 4C on a Samsung washer means water is not entering the machine correctly — a “not filling” error. Samsung’s U.S. support page lists 4C, 1 4C, nF, and 4E together for this fault. Newer displays often show 4C instead of 4E, but the checks are the same: the taps, hoses, inlet screens, and drain-hose setup.

Last updated: November 17, 2026.

This is not a drain-pump code and not a suds code. If the display says Sud, SUd, or 5D, see why a Samsung washer says Sud. For more washer guides, visit the washing machines hub.

Safety first

Unplug the washer, or switch off its breaker, before you pull it forward or work at the back. Shut both water taps off before you disconnect any fill hose, and open the taps slowly when you reconnect so you can check for leaks. Do not remove the screw that holds the drain hose against the back of the washer.

How to fix a Samsung washer 4E or 4C code

  1. Open both water taps fully and leave them open while the washer runs. A partly closed valve is a common reason the machine cannot fill.
  2. Check the fill hoses. Samsung says both the hot and cold supply hoses must be connected to the matching inlets (hot to hot, cold to cold) and must not be bent or kinked. If the hot line is not connected, the washer can show this error when it calls for hot water, including on some cycles labeled Cold. Samsung also says not to use Flood Safe hoses.
  3. Check the drain hose. It should be inserted properly and not kinked. On Samsung’s U.S. error-code page, it should not be inserted less than 6 inches or more than 8 inches into the drainpipe. Do not remove the screw and holder that keep the drain hose against the back of the washer. If that holder is missing, Samsung says service is required.
  4. Reset power. Unplug the washer, or flip its circuit breaker, for 1 minute. Restore power and try a cycle.
  5. Clean the inlet mesh filters. If sediment in the water supply has built up, it can block water from entering. Shut the taps off, disconnect the hoses from the back of the washer, and look inside the washer’s connections. If you see debris, carefully remove the filters, clean them, reinstall them, reconnect the hoses, and open the taps fully again.

If 4E or 4C is gone and the tub fills normally, you can return the washer to its usual place, keeping the hoses unkinked. If the code returns, go to the service steps rather than forcing another cycle.

Samsung lists a different group of codes — 4C2, 4E2, CE, 14C2, and nF1 — when the water on the cold supply is extremely hot, usually because the hot and cold hoses are swapped. The fix is to connect cold to the cold inlet and hot to the hot inlet (typically blue to blue and red to red). Samsung says that code does not, by itself, mean the washer needs service.

When to call a technician

If you have confirmed the taps are open, the hoses are correct and unkinked, the drain hose is installed as Samsung describes, the inlet screens are clean, and a 1-minute power reset does not clear 4E or 4C, Samsung’s washer error-code page says to request service through Samsung Support. A failed inlet valve or another internal part is a technician job. Have your model number ready.

Parts and tools

For the checks above you may need a towel, a bucket, and pliers to ease the inlet screens out if they do not come free by hand. Replacement fill hoses should be the type Samsung allows for your machine; the company specifically says not to use Flood Safe hoses. Inlet screens and valves must match your model if they need replacing.

Frequently asked questions

What does 4E mean on a Samsung washer?

It is a not-filling error: water is not entering the washer correctly.

What does 4C mean on a Samsung washer?

The same thing. Samsung’s U.S. support page groups 4C, 1 4C, nF, and 4E together as a not-filling error. Many newer displays use 4C.

Is 4C the same as 4E?

Yes, for this fault. Use the same hose, tap, filter, and drain-hose checks for either code. Do not confuse them with 4C2 or 4E2, which point to a hot/cold hookup problem.

Why is my Samsung washer not filling?

The usual causes are a closed or partly closed tap, a kinked or swapped hose, a clogged inlet screen, or a drain hose that is not inserted to the depth Samsung specifies. After those checks, a 1-minute power reset is the next step.

How do I fix a 4C or 4E error code?

Open both taps fully, straighten and correctly connect the fill hoses, check the drain-hose depth, reset power for 1 minute, and clean the inlet mesh filters if they are dirty. If the code remains, request service.

Related washer codes on this site: LG OE (will not drain), LG UE (unbalanced load), Samsung 4E or 4C (will not fill), Samsung Sud (too many suds), Whirlpool LoC (Control Lock). For more washer guides, see our washing machines hub.

Sources

Resource Links