Do Washing Machines Have Filters?

As an Amazon Associate I earn from qualifying purchases.

Some do, and some do not. Many front-load washers have a drain pump filter you can clean, usually behind a small panel at the front bottom. Many newer top-load washers have no user-serviceable filter at all. Whirlpool says washer filter locations vary by model, not all filters are accessible, and many modern models have no filter. Separately, many washers have small screens where the water hoses connect. These catch sediment from the water supply, not lint. Your owner’s manual is the only reliable way to know what your model has.

Last updated: November 14, 2026.

Below: the three kinds of washer filters, how to find and clean each one, and the signs that one is clogged. Related guides: washer not draining and how to clean a washing machine.

The three kinds of washer filters

Filter Where it is What it catches Who has one
Drain pump filter Front bottom of the washer, behind an access panel or a drawer Lint and forgotten pocket items in the drain water Many front-load washers
Lint filter in the wash basket Inside the basket or under the agitator Lint in the wash water Some top-loaders, including GE Spacemaker models and Maytag models with a Pet Pro Filter; many others are self-cleaning or have none
Inlet screens Inside the hot and cold hose connections at the back Sediment and debris in the water supply Common, in the hoses or the inlet valve

Front-load washers: the drain pump filter

Whirlpool explains that the filter keeps unwanted items like lint and forgotten pocket items out of the pump by straining them from the drain water. If it clogs, the washer may not drain properly. Its product-help page says the filter is typically at the front bottom of the washer and recommends cleaning it every few months, or as needed, depending on use.

Whirlpool’s general steps for models with an accessible filter:

  1. Unplug the washer.
  2. Open the access panel or storage drawer. Put a large, flat container and a towel under the filter, because water will come out.
  3. Release the small drain hose, if your model has one, and drain the water into the container.
  4. Turn the filter counterclockwise to remove it.
  5. Pull off lint by hand, then rinse the filter under running water. A soft brush helps with stubborn debris.
  6. Turn the filter clockwise until it seats fully, replace the drain hose plug, and close the panel.

Check your owner’s manual for your model’s exact location and steps.

Top-load washers: often self-cleaning, or no filter at all

Whirlpool says some newer top-load washers do not need a filter, or have one that is not accessible, in which case you may need a technician. GE Appliances explains that it removed the fine mesh filters from under the agitator because a better pump and larger holes did a better job of removing lint and preventing clogs. On those models, lint is carried out with the drain water, there is no maintenance, and the pump cannot be reached for cleaning.

There are exceptions. GE says its Spacemaker and Space-Saving top-load models made since 2014 have lint filters in the wash basket that you can remove and clean. Some other top-loaders do have one. Maytag says select top-load washers with its Pet Pro System have a built-in Pet Pro Filter that removes pet hair. Older washers varied too. GE’s 1993 and earlier models used a Filter-Flo lint pan on top of the agitator that you emptied after each load.

Inlet screens: the filters most people forget

GE Appliances says washer inlet hoses have screens that catch debris in the water supply, and some washers also have screens inside the hot and cold inlet valve connections. Whirlpool lists clogged inlet screens as a cause of its F8 E1 error, which means the washer is not detecting the right amount of incoming water. It says screens can clog from mineral buildup or debris. GE’s cleaning steps:

  1. Unplug the washer and turn off both water faucets.
  2. Disconnect the hoses from the back of the washer and let them hang into a bucket.
  3. Rinse the screens with water. A soft brush removes sediment. GE says metal screens can be gently pried out with a small screwdriver and plastic screens pulled out with long-nosed pliers.
  4. Replace any screen you cannot get clean, reattach the hoses, turn the water on, and check for leaks.

Whirlpool’s instructions differ slightly: clean the screens in place with a brush (an old toothbrush works), mild soap, and water, without removing them. Follow the method for your brand. Whirlpool also suggests running water through the hoses, and replacing any hose whose flow seems restricted.

Signs a filter needs attention

  • Water left in the drum or a slow drain: check the drain pump filter, if you have one, and the drain hose for kinks. Whirlpool lists both.
  • Slow filling or a water-supply error code: check that both faucets are fully open, the hoses are not kinked, and the inlet screens are clean.

Whirlpool also points out that other things can leave water in the drum: a gentle cycle with a slow spin, an unbalanced load, or too much detergent. See how many ounces of laundry detergent per load.

Frequently asked questions

How often should I clean a washer filter?

Whirlpool recommends cleaning a front-load drain pump filter every few months, or as needed, depending on how much you wash and how much lint builds up.

Where is the filter on my washer?

On front-loaders, it is usually behind a panel at the front bottom. Many top-loaders have no user-serviceable filter. Check your owner’s manual for your model number.

Does my top-load washer have a lint filter?

Probably not one you need to clean. GE says most of its current top-loaders flush lint down the drain with no maintenance. The exceptions are GE Spacemaker models made since 2014.

Can a washer filter be replaced?

Inlet screens can be replaced if cleaning does not work, according to GE. For a damaged drain pump filter, order the part listed for your model number.

Sources

Resource Links